Just How to Install a Bathtub: Install an Acrylic Bathtub and Also Tub Surround
Just How to Install a Bathtub: Install an Acrylic Bathtub and Also Tub Surround
Blog Article
We've noticed this great article pertaining to Tools You Need to Install a New Bathtub listed below on the internet and decided it made sense to relate it with you here.
Mounting a bathtub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently available, the job can relocate immediately; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your bathroom if you have already purchased a new bathtub as well as do not require to transform the setup of your previous water supply pipes.
Your tools and material checklist ought to make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have actually been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the tap and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous type needs to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are valuable in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small factors.
The following objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the bath tub till the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
Turn on the water and also examine all joints and also new pipework for leaks and tighten them if required. Fill up the tub as well as likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub must wait till the bath tub has been utilized a minimum of once as this will certainly resolve it into its final position.
Preparing for the Installation
Firstly, the supporting structure supplied with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its final setting.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a rigid seal, triggering the water to pass through the wall between the bathroom and also the tiling, resulting in issues with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes as well as cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to permit the motion experienced when the bathtub remains in usage. The sealer can break relatively early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads about Installing A Bathtub, I was thinking sharing that piece of content was valuable. For those who enjoyed reading our blog posting kindly be sure to pass it around. Thank you for your time. Visit us again soon.
Schedule Appointment
Report this page